This product has been off the shelf!
KYA-400B Automatic Rebar Tier Tying Machine
Product Description
Product Overview:
KYA-400B Automatic Rebar Tier Tying Machine
The KYA-400B rebar tying tool is lightweight and has a compact, easy to hold grip. The tool is well balanced and is designed to tie rebars as fast as you can pull the trigger. Included with the tool are two lithium-ion batteries. The tool comes with three spools of 21 gauge tie wire.
● Lightweight and compact body.
● Li-Ion higher capacity battery.
● Brushless twisting motor.
● Reduced tying time.
● Reduce the risk of health problems.
● Simple one-handed operation.
Similar Tool:MAX RB398 Rebar Tier, MAX RB397 Rebar Tier, etc.
Vedio
Product Description
Model: | KYA-400B Automatic Rebar Tier Tying Machine |
Air Tool Type: | Rebar Tier |
Tool Diamensions: | 295mmx120mmx375mm |
Net Tool Weight: | 1.90kgs |
Tying Rebar Diameter: | 6-36mm |
Voltage & Capacity: | DC14.4V(4.4AH) |
Charge Time: | Approx.70mins |
Tying Speed Per Knot: | 0.75 seconds |
Ties Per Charge: | Over 2700knots |
Length Of Wire Coil: | 95M |
Diamater Of Wire: | 0.80mm |
Ties Per Coil: | Approx.130ties(3 wraps) |
Wraps Per Tie: | 2 wraps /3 wraps |
Length of Wire For Tying: | 650mm/2 wraps |
750mm/3 wraps |
Rebar Tying Wire 0.80mm
Length: 95m
Tying Strength:0.50KG/CM⊃2;
Tensile Strength:42-47KG/CM⊃2;
Wire Tensile Strength:480m/Pa
Wire Yield Strength:330m/Pa
Elongation:17%
Material Code:Q195 Galvanized Wire
Net weight:0.4kg/reel
Features
Ergonomic rubberized soft handle for increased comfort.
Make ties in under 1 second 2-mode operation provides 2 or 3 wraps.
Fast and easy-load wire reel loading with protective cover.
Brushless Motor eliminates carbon brushes, enabling run cooler , efficiently for longer life.
Delivers up to 130 ties per wire reel allowing for maximum productivity.
Trigger power switch with lock-off feature requires two actions to power the tool.
Ergonomic rubberized soft handle for increased comfort Weighs only 4.19 lbs.
With battery for reduced operator fatigue.
Application
Delivered a cordless tying solution for rebar and steel rod.
Product Manual
No | Normal | Common faults | Warning voice | Possible reason | Inspecting items | Solution | |||||||
1 | Power ON→ The Tip Axis is initialized and the wire-cutter operates automatically. | No operation takes place | No sound emitted | Battery completely empty | Confirm the battery is charged. | Perform normal charge. | |||||||
Electrode plate has been oxidized | Take out the battery and see if the electrode has been brown. | Polish terminal part of battery pack with dry cloth, etc | |||||||||||
Continuous short beeps(Pi,pi,pi…) | Curl guide is open | Open/close curl guide. | Fully close curl guide. | ||||||||||
Binding wire has been entangled around Twist section. | Turn off power and take out the battery to confirm if binding wire has been entangled inside curl guide. | Turn off power, remove binding wire inside curl guide | |||||||||||
Two long beeps | Battery Is empty | Confirm the battery is charged | Perform normal charge | ||||||||||
2 | Trigger ON→ Wire is sent out. | No wire is sent out | Continuous short | Curl guide is open | Open/close curl guide | Fully close curl guide | |||||||
Three short beeps repeated(Pi,pi,pi,Pi,pi,pi, …) | Tie-wire has been run out | Check if the Tie-wire has been run | Set the new tie wire | ||||||||||
Wire caught inside reel | Check if wire inside reel has been loosened and caught | Remove fray on reel | |||||||||||
Cutter section is blocked with foreign substance | Confirm functioning of Cutter section | Either wipe Cutter section with dry cloth or blow it with air | |||||||||||
A wire is caught in the cutter section or Wire guide A | Check if any wire is caught. | Diassemble the cutter section and remove the caught wire | |||||||||||
3 | Binding wire draws a circle. | Curl is disordered and steps out of curl | No sound emitted | Wire, by hitting reinforcing bars, was repelled | check if wire hits reinforcing bars at binding | Pay attention so that wire does not hit reinforcing bars at binding | |||||||
4 | Wire is subject to cutting | No wire cutting takes place. | No sound emitted | Cutter section is blocked with foreign substance | Confirm function of Cutter section. | Either wipe Cutter section with dry cloth or blow it with air | |||||||
5 | Wire twisting takes place | Wire gets entangled | No sound emitted | Wire, by hitting reinforcing bars,was repelled | Check if wire hits reinforcing bars at binding | Pay attention so that wire does not hit reinforcing bars at binding. | |||||||
Binding power is week | No sound emitted | Reinforcing bars is not of designated size. | Confirm size of reinforcing bars to be bound | Use approriate diameter scope | |||||||||
Erroneous handling such as improper application of machine | Confirm how to apply machine to reinforcing bars | Adjust the Torque to a higher lever and insert in vertical direction. Use as tilting at45° | |||||||||||
Twisting-off takes place | No sound emitted | Reinforcing bars is not of designated size | Confirm size of reinforcing bars to be bound | Use approriate diameter scope | |||||||||
Erroneous handling such as improper application of machine | Confirm how to apply machine to reinforcing bars | Adjust the Torque to a lower lever and insert in vertical direction. Use as tilting at45° | |||||||||||
Works properly | Two long beeps repeated(Pi-pi, pi-pi,...) | Low power remains in the battery pack | Confirm the battery is fully charged. | Perform normal charge | |||||||||
Four short beeps repeated(Pipipipi, Pipipipi,…) | The tool is used at high temperature. | Check the temperature at the job site. | Leave the tool and the battery pack at normal temperature in the room for some time. and then continue the operation. |